After brushing the first coat of finish on my shelf project, quite a bit remained in the disposable cup. I didn’t want to pour it back, because that would contaminate the fresh finish that remained in the can. But I didn’t want to waste the finish by throwing it away, either. Knowing the shelves were…

The key to a quick finish is the finish you choose. Finishing is seldom the most enjoyable part of woodworking, so many woodworkers want to get it over within a day – or even an afternoon. Many manufacturers encourage this with their directions, which often produce less than optimal results because they push the process…

Thoughtful finishing and new leaves prepare this classic for the next 100 years. This old table looks like a prime candidate for refinishing. Scrub off the old finish, sand out all the dings and scratches, spray on a catalyzed lacquer finish and it would look brand new. But in my opinion, doing this would rob…

在短短90秒Logan艾尔l the main parts of a metal body hand plane. Interested in learning more? Check out the article Handplanes for Beginners. For Basics Week we’re presenting a special offer on our PopWood+ membership, where you can save 25% off your first month or full year when…

An ancient European tool that still has a place in the modern American shop. Editor’s note: This article originally appeared in the November 2008 issue of Popular Woodworking Magazine. Why should you own a bowsaw? Why not? You have many other tools that you use only when you need them. Seriously, if you make 18th-century-style…

This versatile hand tool should be every woodworker’s first plane purchase. As a “professional woodworker” I often get asked what’s the best bang-for-the-buck tool by people getting into this craft. My response is always to ask if they have a good quality block plane. I know, it’s not the big, awesome aircraft carrier-like jointer plane….

令人费解的润滑。编者按:这篇文章originally appeared in the August 2010 issue of Popular Woodworking Magazine I ran out of mutton tallow this morning! I searched my tool chests, under the benches and in the drawers hoping to find just enough white magic to ease the passage of the big jointer plane up and…

Practice Traditional Building Joinery on a Smaller Scale Project #2104 • Skill Level: Advanced • Time: 2 Weeks • Cost: $300 During my 14 years living in Europe, I marveled repeatedly at how these beautiful timber framed structures had withstood the test of time—I remember one awe-inspiring timber framed house near Wiesbaden, Germany, with a placard on…

I use biscuit joints in lots of small projects, particularly for joining rails to legs. I usually reference from the bottom of the plate joiner rather than use its fence. When I want to make an offset joint, I cut the slots in the rails first. Then I add a large shim plate to the…

When using my miter saw, I’ve found that the easiest way to sneak up on a line is to use a stack of sticky notes. First, set a stop block to cut your part slightly oversize (1/16″ is plenty). Attach a thin pile of sticky notes to the stop block, make a cut, and then…

I use a portable circular saw to break down plywood and other sheet goods into manageable pieces before bringing them to the table saw for final sizing. I prefer to do the job on sawhorses rather than crouching on the floor. Unfortunately, you normally need three or four horses to provide enough support to prevent…

The next time you use your jigsaw, forget about hauling out the sawhorses or cantilevering a hard-to-hold workpiece off your bench. Extruded polystyrene insulation board, the rigid pink sheets used in housing construction, makes sawing easy, whether you’re cutting a small piece of hardwood or a full sheet of plywood. During the cut, the workpiece…

After Dave excavated the bowl and trimmed the end grain, he sanded the inner bowl and was ready to add one more element – a stabilizing leg that would level the bowl. As I mentioned last week, each of the crotch bowl arms had a different thickness, and once laid flat on a surface, the…

Last Memorial day weekend, I returned to Peters Valley School of Crafts to teach a Live Edge furniture-making class. Our class was on the short side; concise and intensive. My three students worked hard and completed their project short of applying a coat of finish before they left the Valley’s, as we call it, spectacular…

Before we start carving, here are a few basic carving principles. Stop cuts are cuts that protect areas you don’t want to remove. These simply sever the fibers and define shapes, allowing you to make cuts into them without cutting past them. Next, remember you can always take more off but not add it back….

When I first started teaching the 8th-grade stool-making class, I needed to find an easy method for my students to mark the leg length accurately before trimming them to a parallel surface with the seat. While there are various techniques available, such as using wedges to level the seat and scribing a line on the…

How do you know if the table on your drill press is square? Not more-or-less square, but precisely square? I’ve adopted an old machinist’s trick, using a very simple jig. To make it, you’ll need a hardwood arm, two 5/16″ carriage bolts that are 2″-3″ long, four nuts and four washers. First, make the arm….

Sometimes it’s fun to build a gadget just because it’s a neat idea. There are many ways to draw a centerline, for example, but this method is very clever. It doesn’t require any measuring or trial-and-error adjustments. To build the marker, you’ll need two hardwood bars 3/4″ x 1″ x 12″, two Plexiglas links 1/4″…

The blade of a marking gauge must be as sharp as a scalpel in order to cut a fine line across the grain. Sharpening it can be very difficult because it’s so small. I solved that problem by making a gauge that accepts snap-off utility knife blades. I use epoxy to glue the blade into…

Accurately drilling an angled hole with a hand drill is a challenge – particularly if you’re using a brad point or Forstner bit. This angled drilling guide solves the problem handily. The guide keeps the drill bit from wandering as it enters the stock. It can be cut at any angle, and its alignment marks…

When using my miter saw, I’ve found that the easiest way to sneak up on a line is to use a stack of sticky notes. First, set a stop block to cut your part slightly oversize (1/16″ is plenty). Attach a thin pile of sticky notes to the stop block, make a cut, and then…